RF-BM-ND06 FCC BLE5.0 Bluetooth low Energy USB NFC mesh Module Nordic nRF52840
RF-BM-ND06 an RF module based on Nordic Bluetooth 5.0 / Bluetooth mesh / Thread / 802.15.4 / ANT / 2.4 GHz multiprotocol SoC nRF52840-QIAA-R with best-in-class 32-bit ARM? Cortex?-M4 processor. It integrates a 32.768 kHz and a 32 MHz crystal, a power filter, an antenna matching, and a meander line inverted-F PCB antenna. It features high-performance digital interfaces, robust connection distance, and rigid reliability. It supports BLE stack v5.0 and can be preprogrammed with a serial interface communication protocol for simple programming. 1.27-mm pitch stamp stick package for easy assembling and cost-effective PCB design. All pins of RF-BM-ND06 are pulled out.
Parameters of RF-BM-ND06
Chipset | nRF52840QIAA-R |
Supply Power Voltage | 1.7 V ~ 5.5 V, recommended to 3.3 V |
Frequency | 2402 MHz ~ 2480 MHz |
Transmit Power | -20.0 dBm ~ +8.0 dBm (typical: 0 dBm) |
Receiving Sensitivity | -96 dBm |
GPIO | 48 |
Crystal | 32 MHz, 32.768 kHz |
RAM | 256 KB |
Flash | 1 MB |
Package | LGA Packaging |
Frequency Error | ±20 kHz |
Dimension | 24.0 mm x 20.5 mm x (2.20 ± 0.1) mm |
Type of Antenna | PCB Antenna |
Operating Temperature | -40 ℃～ +85 ℃ |
Storage Temperature | -40 ℃～ +125 ℃ |
module module
Recommended Footprint
Pin Attributes
Pin Functions of RF-BM-ND06
Pin | Name | Chip Pin | Pin Type | Description |
1 | P0.12 | SIO_12 | - | - |
2 | VCC | Power 1.7 V ~ 3.6 V | - | 1.7 V ~ 3.6 V |
3 | VDD_HV | Power 2.5 V ~ 5.5 V | - | 2.5 V ~ 5.5 V |
4 | VDD_USB | 4.35 V ~ 5.5 V | - | 4.35 V ~ 5.5 V |
5 | D- | D- | Data- | USB- |
6 | D+ | D+ | Data+ | USB+ |
7 | P0.13 | GPIO_13 | - | LED |
8 | P0.14 | GPIO_14 | - | LED |
9 | P0.15 | GPIO_15 | - | LED |
10 | P0.16 | GPIO_16 | - | LED |
11 | P0.17 | GPIO_17 | QSPI_CS | LED |
12 | P0.18 | nRESET | - | System reset (active low) |
13 | P0.19 | GPIO_19 | QSPI_CLK | - |
14 | P0.20 | GPIO_20 | QSPI_DIO0 | - |
15 | P0.21 | GPIO_21 | QSPI_DIO1 | - |
16 | P0.22 | GPIO_22 | QSPI_DIO2 | - |
17 | P0.23 | GPIO_23 | QSPI_DIO3 | - |
18 | P0.24 | GPIO_24 | - | - |
19 | P0.25 | GPIO_25 | - | - |
20 | P1.00 | GPIO_1.00 | - | - |
21 | SWDIO | SWDIO | - | Serial wire debug I/O for debug and programming |
22 | SWCLK | SWCLK | - | Serial wire debug clock input for debug and programming |
23 | NFC1 | NFC1/SIO_09 | - | - |
24 | NFC2 | NFC2/SIO_10 | - | - |
25 | P1.01 | GPIO_1.01 | - | - |
26 | P1.02 | GPIO_1.02 | - | - |
27 | P1.03 | nAutoRUN | nAutoRUN | FTDI USB_DTR via jumper on J12pin1-2. |
28 | P1.04 | GPIO_1.04 | - | - |
29 | P1.05 | GPIO_1.05 | - | - |
30 | P1.06 | GPIO_1.06 | - | - |
31 | RF_OUT | RF-interface | - | - |
32 | P1.07 | GPIO_1.07 | - | - |
33 | P1.10 | GPIO_1.10 | - | - |
34 | P1.11 | GPIO_1.11 | - | - |
35 | P1.12 | GPIO_1.12 | SPI_CS |
|
36 | P1.13 | GPIO_1.13 | - | - |
37 | P1.14 | GPIO_1.14 | - | - |
38 | P1.15 | GPIO_1.15 | - | - |
39 | P0.03 | GPIO_0.03 | - | Temperature sensor analog |
40 | P0.02 | GPIO_0.02 | - | Internal pull low. External pull high to enter VSP services. |
41 | P0.28 | GPIO_0.28 | - | - |
42 | P0.29 | GPIO_0.29 | - | - |
43 | P0.30 | GPIO_0.30 | - | - |
44 | P0.31 | GPIO_0.31 | - | - |
45 | P0.26 | GPIO_0.26 | I2C_SDA | I2C RTC chip. I2C data line |
46 | P0.27 | GPIO_0.27 | I2C_SCL | I2C RTC chip. I2C clock line. |
47 | P0.04 | GPIO_0.04 | SPI_MISO | SPI EEPROM. SPI_Eeprom_MISO, Input. SPIOPEN in smartBASIC selects SPI function; MOSI and CLK are outputs when in SPI master mode |
48 | P0.05 | GPIO_0.05 | UART_RTS |
|
49 | P0.06 | GPIO_0.06 | UART_TX |
|
50 | P0.07 | GPIO_0.07 | UART_CTS |
|
51 | P0.08 | GPIO_0.08 | UART_RX |
|
52 | P1.08 | GPIO_1.08 | SPI_MOSI |
|
53 | P1.09 | GPIO_1.09 | SPI_CLK |
|
54 | P0.11 | GPIO_0.11 | - |
|
